Pereiti prie turinio

Mon–Fri 8–18

We work across Lithuania
Advice

Getting ready for the heating season: eight steps to a warm winter

Updated 10 November 2026 · 4 min read · Prepared by the technicians of Visų katilų remontas

In summer the boiler rests or only heats hot water. The radiators stand cold, the thermostat batteries run down and air slowly collects in the system. On the first cold autumn evening all of this shows up at once, usually when technicians' diaries are already full. The good news is that getting ready is not difficult. We have listed eight steps worth taking in August or September. Most of them you can do yourself in one afternoon.

In brief

  • Book the boiler service in summer or September, while technicians are not yet busy.
  • Before the season, switch the heating on for a test while the weather is still warm.
  • Bleed the radiators and then check the pressure.
  • Replace the thermostat batteries and open the thermostatic radiator valves.
  • Make sure the flue terminal outside and the condensate pipe are clear.

Why it pays to prepare in advance

Many boiler problems only show up when the boiler starts working at full capacity. In summer, when it only heats hot water, a minor malfunction can go unnoticed. In autumn it becomes a problem, and that is when the wait for a technician is longest. So all the jobs described below are best done while the weather is still warm: if something does not work, you will have time to put it right without rushing and without a cold house.

JanFebMarAprMayJunJulAugSepOctNovDec heating season (usually) best time for servicing
The heating season in Lithuania usually lasts from October to April. The most convenient time to prepare is summer and September.

1. Book the boiler service

Manufacturers specify that the boiler should be checked and serviced every year. During the service the technician measures combustion, cleans the boiler and the trap, and checks the expansion vessel and the tightness of the gas components. We describe exactly what is done in the article "Annual gas boiler servicing". If you book the service in summer, you will avoid the autumn queues, and the technician will have time to replace any parts that have to be ordered.

2. Switch the heating on for a test

One evening in September, switch the heating on briefly: switch the boiler from summer to winter mode and turn up the room thermostat. Within half an hour you will see whether the boiler fires, whether all the radiators warm up and whether any error codes appear. If something is wrong, it is not yet a disaster but a reminder that it is time to call a technician.

3. Bleed the radiators

Over the summer air collects in the system, especially in the highest radiators. Air stops the water circulating, so the top of the radiator stays cold and the system sometimes creaks and gurgles. After the test run, wait until the radiators have cooled down, because hot water can scald. Then, starting with the lowest radiator, open the bleed valve in the top corner and hold it open until water without bubbles flows instead of hissing air. This is described step by step in the guide to bleeding radiators.

4. Check the pressure

After bleeding, the pressure in the system drops. Once the system has cooled, look at the pressure gauge. For most domestic boilers the cold-system pressure should be between 1 and 2 bar, and the exact limit is given in the boiler's manual. If the pressure is too low, top up the system through the filling tap. You will find how to do this safely in the article "Boiler pressure".

5. Prepare the thermostat and radiator valves

The batteries of a wireless room thermostat are best replaced before the season, rather than waiting for them to run out on a January night. Check that the time and the heating programme are set correctly. Fully open any thermostatic radiator valves that were closed for the summer: the pin of a thermostatic valve that has been closed for a long time sometimes sticks, and the radiator does not warm up. If the radiator still stays cold after you open the valve, tell the technician.

6. Check what is outside

The flue terminal outside must be clear: no nests, leaves or other obstructions. The condensate pipe of a condensing boiler is often routed to the same place. Manufacturers specify that a condensate pipe running outdoors must be of sufficient diameter and insulated, because if it freezes it stops the boiler. If the pipe froze last year, tell the technician during the service.

7. Clear the space around the boiler

In summer the boiler room or cupboard often turns into a storeroom. There must be free space around the boiler for the technician and for air circulation, and no flammable items on or near it. If the boiler takes its air from the room, do not cover or block the ventilation openings.

8. Think about safety

Autumn is also a good time to check your safety equipment. If you have a carbon monoxide (CO) detector, press its test button and replace the batteries if necessary. If you do not have one, it is an inexpensive and useful purchase for any home where fuel is burned. Also remind your family what to do if they smell gas.

If you smell gas: do not switch any switches on or off, do not light a flame and do not smoke, open windows and doors, close the gas tap if possible, warn others and go outside. Once outside, call 112.

Short checklist

  1. June–August: book the boiler service.
  2. September: test run of the heating.
  3. Once the radiators have cooled: bleed the air.
  4. Once the system has cooled: check the pressure and top up if necessary.
  5. On the same day: thermostat batteries, programme, radiator valves.
  6. Outside: flue terminal and condensate pipe.
  7. In the boiler room: free space, unblocked ventilation openings.
  8. Safety: carbon monoxide detector and a family agreement on what to do.

Frequently asked questions

When is the best time to get the boiler ready for winter?

In summer or in September. It is easier to book a technician then, and if the test run reveals a fault, you will have time to fix it before the cold weather.

Does the boiler have to be serviced every year?

Manufacturers specify that the boiler should be checked and serviced every year, and some make the warranty conditional on regular servicing. You will find the specific terms in your boiler's warranty card.

Why does the pressure need checking after bleeding?

Water takes the place of the air that was bled, so the pressure in the system drops. If it becomes too low, the boiler stops and shows an error code.

Do I need a carbon monoxide detector if the boiler is new?

A detector is useful in any home where fuel is burned, regardless of the boiler's age. It does not replace the annual service, but it warns you if something goes wrong.

Need a technician?

We have worked across Lithuania since 2016 and arrive with spare parts. Describe the situation or give us a call.

Tips: Getting ready for the season

Write the boiler manufacturer and model or attach a photo of the rating plate – we will call you and help.

+370 630 13331Request a service

Sources

  1. Vaillant ecoTEC plus VU/VUW, installation and maintenance manual, doc. 0020308118_05 (2023-05-31): safety section 1.3, pressure 9.7, maintenance table (Appendix B)
  2. Immergas Victrix Tera V2 24-35 Plus EU, user and installation manual, doc. 1.047821ENG

This article is general information. Always follow the manual of your own boiler, and leave work on gas and combustion components to a certified specialist.

More tips

CallRegister