Annual gas boiler servicing: what the technician does and why it matters
A gas boiler works quietly and out of sight. Over a heating season it switches on and off countless times, heats water by tens of degrees and removes flue gases that we never see. As long as there is heat and hot water, we rarely think about it. Yet this is exactly the kind of appliance that most needs regular servicing: most faults develop gradually and without any warning signs. In this article we explain what manufacturers require every year, what actually happens during an annual service and how to prepare for it.
In brief
- Manufacturers require the boiler to be checked and serviced every year. If national rules require it more often, those rules apply.
- The most important part of the check is combustion analysis: an instrument measures the CO and oxygen content of the flue gases.
- Some parts are replaced at set intervals; for example, the Vaillant control electrode at least every 5 years or 20 000 operating hours.
- The inspection of a building's gas system carried out by ESO is not a substitute for boiler servicing.
- It is most convenient to book servicing in summer or early autumn, before the heating season.
Why every year if the boiler works well
Boiler faults rarely come suddenly. More often they creep up quietly. The heat exchanger gradually becomes coated with deposits, and the same heat is transferred to the water with more and more difficulty. The ignition and control electrodes wear, the spark weakens and the flame signal becomes unstable. Dirt collects in the condensate trap. The air-to-gas ratio changes, and with it the quality of combustion. Each of these changes is barely noticeable on its own, but together they mean higher bills, noisier operation and, one day, a cold house.
The most important reason for servicing is safety. When gas burns poorly, carbon monoxide (CO) is produced. It has neither smell nor colour, so it cannot be detected without an instrument. An annual check is the only way to make sure that the boiler burns cleanly and that the flue gases go outdoors only.
What manufacturers and legislation say
In manufacturers' instructions the servicing work is set out in a table with intervals. For example, the Vaillant ecoTEC plus installation and maintenance instructions contain a list of 39 items, and most of them are marked "annually". The same document stresses that these are the manufacturer's minimum requirements: if national rules set more frequent checks, those must be followed.
Many manufacturers link servicing to the warranty. The Vaillant instructions (United Kingdom edition) state that, to keep the warranty, the boiler must be serviced every year by a competent person. You will find the specific warranty terms for your boiler on the warranty card or in the seller's documents. It is worth reading them and keeping the report from every service: it is the best proof that the boiler has been looked after.
Two different checks are often confused. The building's gas system, that is, the gas service pipe and the internal gas pipework, is inspected periodically by the distribution operator ESO. In residential buildings this is done at least once every five years. This inspection covers the gas pipework, not the inside of the boiler: it does not clean the heat exchanger, does not measure combustion and does not replace the annual servicing required by the manufacturer.
What happens during an annual service
A proper annual service is not a quick glance under the cover. It is methodical work that follows much the same sequence in boilers from all manufacturers. Below we describe it following the list in the Vaillant instructions. The work for other manufacturers is very similar, and the exact list is in each boiler's manual.
1. Conversation and error history
The technician asks whether there have been any problems during the year: strange noises, shutdowns, pressure drops. Then they review the error history stored in the boiler's diagnostics system. Sometimes it tells more than the owner can, because the boiler also remembers faults that cleared by themselves.
2. Inspection
The technician checks that the flue and its terminal outdoors are installed correctly and are not blocked, that the boiler is fixed securely and that the connections are tight. In condensing boilers the condensate pipe is checked separately: whether it is tight and routed correctly, and whether any section running outdoors is protected against freezing.
3. Combustion analysis
This is the most important step. The probe of a flue gas analyser is inserted into the test point on the flue, and the instrument shows how much carbon monoxide (CO) and oxygen (O₂) the flue gases contain. From these figures the technician judges whether the boiler burns gas cleanly and whether the air-to-gas ratio is correct. The gas flow rate is also checked against the boiler's data plate.
The Vaillant instructions set out a clear sequence of steps if the measurement shows too much CO (more than 350 ppm): first the flue and its length are checked, then the control electrode is replaced, then the combustion chamber is inspected, and if that does not help either, the manufacturer's service team is contacted. This sequence matters: poor combustion is not something to be "adjusted" with a screwdriver; the cause has to be found first.
4. Cleaning
Dust and dirt are cleaned from the inside of the boiler. The condition of the heat exchanger is inspected for corrosion, rust and damage. The condensate trap is cleaned and refilled with water, because an empty trap can let flue gases through. If necessary, the heat exchanger is cleaned and the burner and the combustion chamber insulation are checked.
5. Gas components and tightness
The technician checks that the gas isolation valve and the service valves work and, once the boiler has been reassembled, makes sure there are no leaks of gas, flue gas, water or condensate anywhere.
6. Heating water and pressure
Heating water may seem unimportant, but the life of the heat exchanger depends on it. The technician checks whether the water is clear, whether it contains corrosion inhibitor and what its pH is. According to the Vaillant instructions, if the pH is below 8,2 or above 10, the system must be flushed and the water treated. The pre-charge pressure of the expansion vessel and the system pressure are checked at the same time. We cover this in more detail in the article "Boiler pressure".
7. Test run and report
The reassembled boiler is started: heating is tested and, if the boiler also produces hot water, so is the hot water function. Air is bled if necessary. Finally, the service interval is reset in the boiler and the measurement results are recorded in a report, which is given to you.
What is checked or replaced less often
Not everything is done every year. Some work is carried out "regularly", that is, when the condition requires it, and for some parts the manufacturer specifies a set interval.
| Work | When |
|---|---|
| Replacing the control electrode | As required, but at least every 5 years or 20 000 operating hours (whichever comes first) |
| Re-checking the oxygen content (air ratio) | As required, but at least every 2 years |
| Cleaning the heat exchanger, checking the burner and insulation panels | Regularly, depending on condition |
| Checking and topping up the pre-charge pressure of the expansion vessel | Regularly |
| Cleaning the cold water inlet strainer (in boilers that produce hot water) | Regularly |
The intervals are given according to the Vaillant ecoTEC plus instructions. They may differ for boilers from other manufacturers, so the technician follows the manual of the specific model. Our technicians usually carry the parts that may need replacing, such as electrodes or gaskets, and the less common ones can be found by boiler model in the online shop.
When is the best time to book
Manufacturers talk about a year, not a season, but timing does matter. In autumn, once the heating season has started, service companies get the most calls and you have to wait longer for a technician. Besides, a boiler that stops in October or November is a far bigger problem than one that stops in July.
We therefore advise planning the service between June and September, at roughly the same time each year. If you would like us to remind you, choose a service plan: we then keep the full work history of your boiler.
How to prepare for the technician's visit
- Clear the space. There must be free access to the boiler, and the flue terminal outdoors must not be obstructed.
- Write down the boiler model. You will find it on the manufacturer's label, usually on the underside of the boiler. The technician will then bring the right parts.
- Recall what happened during the year. Error codes, strange noises, pressure drops, fluctuating hot water temperature: every detail helps.
- Get the documents ready. The manual, the warranty card and the reports from previous services, if you have them.
What you can do yourself between services
Servicing the inside of the boiler is a job for a specialist, but day-to-day observation is in the owner's hands. Every few weeks take a look at the pressure gauge: if the pressure has dropped, you can top up the system yourself. At the start of the heating season, bleed the radiators. In winter, especially in freezing weather, keep an eye on the condensate pipe if it runs outdoors. A frozen pipe stops the boiler. And most importantly: write down every error code, even if the boiler then restarted by itself.
Important. Do not dismantle or adjust the boiler casing, the combustion chamber or the gas components yourself. Work on gas and combustion components and combustion measurement must be carried out by a certified specialist. If you smell gas: do not light a flame or smoke, do not switch electrical switches on or off, do not use a phone indoors, open the windows and doors, close the gas isolation valve if possible, warn others and go outside. Once outside, call the emergency number 112.
How much it costs
Our price for an annual service of a domestic gas boiler is 130 €. The price and what it includes are on the page "Annual gas boiler servicing", and the prices of all services are on the prices page. If the service shows that a part needs replacing, the technician first tells you the price and replaces it only with your consent.
Frequently asked questions
How often does a gas boiler need servicing?
Manufacturers require the boiler to be checked and serviced every year. For example, in the Vaillant ecoTEC plus instructions most servicing tasks are marked with the interval "annually". If national rules require it more often, those rules apply.
The boiler works well. Does it still need servicing?
Yes. Many changes cannot be seen at first: the heat exchanger becomes coated with deposits, the electrodes wear and combustion changes. An annual check spots them in time, and combustion analysis shows whether the boiler burns gas cleanly.
Does the ESO gas system inspection replace boiler servicing?
No. ESO inspects the building's gas system: the gas service pipe and the internal gas pipework. This inspection does not clean the boiler, does not measure combustion and does not replace the annual boiler servicing required by the manufacturer.
How long does an annual boiler service take?
Usually about an hour or two. The time depends on the boiler model, its condition and how much cleaning is needed.
Does the warranty lapse without annual servicing?
Many manufacturers make the warranty conditional on regular servicing. You will find the specific terms on your boiler's warranty card. Keep the report from every service.
Can I service the boiler myself?
You can monitor the pressure, top up the system and bleed the radiators. Servicing of the inside of the boiler and of the gas and combustion components, as well as combustion measurement, must be carried out by a certified specialist.
Need a technician?
We have worked across Lithuania since 2016 and arrive with spare parts. Describe the situation or give us a call.
Sources
- Vaillant ecoTEC plus VU/VUW, installation and maintenance instructions, doc. 0020308118_05 (2023-05-31), Appendix B "Inspection and maintenance work" and section 2 "Warranty"
- Immergas Victrix Tera V2 24-35 Plus EU, user and installation manual, doc. 1.047821ENG
- ESO, "Maintenance of gas supply systems in buildings" (in Lithuanian)
- LRT, "Kaunas resident has waited 30 years for a gas appliance inspection…" (2024-03-04), ESO comment on gas system inspections every 5 years
This article is general information. Always follow the manual of your own boiler, and leave work on gas and combustion components to a certified specialist.